The Features of Gas Burner Valves

 This is the features of gas burner valves: Adjustable gas flow / 1/8" pipe size/Flat down stem /2" from the center of the inlet to the end of the stem
3 3/4" overall length/Can be used with natural gas patio heater or liquid propane Manufacturers & Models/APW Wyott (2068200)/American Range (As needed)/Connerton (LRB-16)/Garland (1086586)/Imperial (1610)/Jade (44-110)/Montangue (2403-1)/Rankin Delux (RDLR-10)/Royal (1628)/US Range (227006)/Wolf (719221).

Introduce Gas Burner Safety Valve

The gas burner safety valve for free standing cookers.with the safety desgin to be more safey and connector to a micorswitch to the auto ignitor.the gas Burner Valve with a bracket at the top of the shaft.  

More About Gas Valves & Controls

Gas valves are used to regulate natural gas or liquid propane in heating systems. Gas valves vary in capacity (cubic ft of gas), inlet/outlet size, and type (standing pilot, slow opening, and step opening).

Gas brass safety valve and controls must match the heating system's fuel type. Liquid propane and natural gas conversion kits are available if the valve must be converted to meet a system's requirements. After the system type is verified, the system's capacity must be determined. Whether a normally open or normally closed gas valve is selected depends on the expected usage frequency of Copper Gas Valves.

A solenoid valve uses a solenoid to actuate the valve. This allows the flow of water, gas, or air to be controlled with electricity. A solenoid is a coil of wire that becomes magnetized when an electric current passes through it. Solenoids often have a hole in their center and a protruding metal rod that is pushed or pulled by magnetism when power is applied. Solenoid valves are best for continuous on/off cycling.

How to Remove Burner Valve for Rebuilding

The step one is to shut off the gas.You will need to keep the gas shut off until return of rebuilt of burner valves.The steptwo is to remove knobs & control panel.For help on how to remove control panels,wedgewood flat control panel,"kool kontrol" o'keefe & merritt control panel,flat o'keefe & merritt control panel,1930's style o'keefe & merritt control panel.The step three is to dismount burner valve from manifold unscrew burner valve usually in a counter clockwise rotation.

What is a good type of Gas cooking valves on our website.

The company mainly products for Gas cooking valves used in free standing cooker,built-in hobs. The company does not only solve the common problem of high-temperature block and weak durability of gas valves, but also make the high-temperature resistance of the products reach 130℃. The durability reaches 100,000 times, far exceeding state and CE standard and hence making.Cooking valve win at the beginning and take the lead in long term. Cooking valve make your products safer, more comfortable and more durable.

The Introduction of gas grill

Gas Grill Valves typically use propane (LP) or natural gas (NG) as their fuel source, with gas-flame either cooking food directly or heating grilling elements which in turn radiate the heat necessary to cook food. Gas Heater Control Valve are available in sizes ranging from small, single steak grills up to large, industrial sized restaurant grills which are able to cook enough meat to feed a hundred or more people. Gas grills are designed for either LP or NG, although it's possible to convert a grill from one gas source to another.

More About Gas Valves & Controls

Types of Gas Grill

A recent trend in Gas Grill Valve is for manufacturers to add an infrared radiant burner to the back of the grill enclosure. This radiant burner provides an even heat across the burner and is intended for use with a horizontal rotisserie. A meat item (whole chicken, beef roast, pork loin roast) is placed on a metal skewer that is rotated by an electric motor. Smaller cuts of meat can be grilled in this manner using a round metal basket that slips over the metal skewer.
Another type of gas grill gaining popularity is called a flattop grill. According to Hearth and Home magazine, flattop grills "on which food cooks on a griddlelike surface and is not exposed to an open flame at all" is an emerging trend in the outdoor grilling market.

A small metal "smoker box" containing wood chips may be used on a gas oven safety valve to give a smoky flavor to the grilled foods. Although, barbecue purists would argue that to get a true smoky flavor (and smoke ring) the user has to cook low and slow, indirectly and using wood or charcoal. Gas grills are difficult to maintain at the low temperatures required (~225-250 °F), especially for extended periods.

Fuel Machine

First, check the fuel prior to commissioning the machine has three aspects:
1. Check diesel fuel is in place, the fuel line is clean smooth, whether the valve is turned on.
2. Have pipeline leakage phenomenon, pipeline installation is reasonable.
3. Into the oil return line is installed correctly, the return line is not allowed to install gas valve
Second, the fuel inside the inspection
1. Nozzle burning machine is installed and whether the ignition electrodes adjusted.
2. Motor rotation direction is correct.
3. External circuitry coupled to meet the requirements.
4.Gas Control Valves are closed
5. According to the burner line conditions were cold simulation
Burner selection is a more complex technical problem, the user can choose a burner according to the following conditions:
1, the fuel type
First, what the user wants to determine its own fuel, according to their own choice of selected fuel burners. For example, the choice of fuel is a diesel fuel burner; the choice of fuel is a gas gas burner.
2, the degree of automation requirements
After the user in the selection of fuel should be used in accordance with the requirements of their economic capacity and equipment nozzle (burner) or use automatic burner. Generally speaking, the choice of nozzle (burner) is low cost, but the problem is difficult to ensure security ; use automatic burner higher cost, but do not need to configure their own fans and control system, easy operation, high precision temperature control, safe and secure.

Gas Water Heater Troubleshooting

1, the valve is not open: In theWater Heater Gas Valvesis opened, there is no fire to boil water, mainly due to a ruptured eardrum outlet nozzle, the valve can not open the top. Remedy is to buy a new eardrum replaced. During the replacement process, to anti-Stop the hollow screws on hold against the eardrum, otherwise, even if replaced with a new drum, the valve can not open the top.
 2, ignition unfavorable: Ignition difficulties or misfiring nozzles and the main reason is fire carbon heater, or valve gauze filter fouling. Remedy is to check the fire nozzle and electric heaters, such as found in soot, cleaned; if the valve fouling gauze filter, you can unscrew the inlet pipe, remove the filter gauze washed with water after cleaning the water pipes installed .
3, burning odor: Hose is not connected or there are cracks and leaks, it should be properly installed or replace the hose; oil or debris also easy to cause odor, it should be cleaned or cleared on firearms.
4,  combustion is incomplete: incomplete combustion will lead to an increase in harmful gases, serious environmental pollution, mainly because of the heat exchanger and the main burner clogging. Remedy is to check the heat exchanger and the main burner, and washed, so smooth.
5, copper leaks: the most easily damaged is facing long fire place. The main reason is the disruption of water supply, the case of low water pressure or fire for a long time is not long off, the copper wall burn. When emergencies, will be temporarily fuse plug holes. After use, remove the Gas Valve For Water Heater, put the best water in the water, electric iron will leak eye weld. In order to prevent the premises being burned again, you can install the piece of iron on copper, used to block the long flame.
6, heat storage piece fouling: fouling thermal storage piece, it will affect the absorption of heat and ventilation. The main reason is to use a long time, the indoor air does not circulate. Remedy is Huigou remove heat storage sheet between Huigou if too thick, can be ground into a hacksaw blade-shaped ramp, gently scrape the grime clean and scraped with a bicycle pump Huigou blown clean . Also steel blade or other tool storage allocated to the uniform distribution of the heat sink, so as not to affect the storage of heat and ventilation.
7, burning yellow flame: the gas too much pressure relief valve should be replaced; inadequate supply of fresh air to the exhaust fan or open windows and doors immediately change the fresh air; there is debris blocking mix of Aikido and should be cleaned up.
8, no hot water: valve or pipe blockage, to replace valves, check valves and pneumatic piping; water temperature is low, you should turn up the gas supply, transfer a small amount of cold water supply; water control system the failure to invite professional and technical personnel maintenance.

What is the normal gas stove flame color? how is it

  first  : Good burner flame was blue, fire strong, uniform flame height size.
second : gas stove valves flame adjustment method
1, the valve open kitchen to the maximum. In this case, if the flame inside and outside the cone is not clear, even yellow, indicating insufficient air volume, damper increase the amount of time into the air, until the flame inside and outside the cone clear, it becomes light blue.
2, gas valve off a small stove. Small fire generally not damper. If the flame becomes shorter, indicating the amount of air is too large, the valve slightly smaller adjusted.
3, repeated adjustment, the flame can get qualified under any state.
third: gas stove flame problem analysis and solution
1, the burner fire cover fire holes are blocked with dirt, mixing burner gas outflow obstruction, clean up dirt fire hole.
2, nozzle clogging, unscrew the nozzle clean.
3, the regulator air inlet and nozzle clogging rust, impede the outflow of gas bottles in vivo, the replacement of qualified regulators.
4, fold flat ventilation hose blocked, straighten the hose.
5, another gas is about used up, the valve is not fully open and other reasons we should pay attention, you can take the appropriate action to resolve.

Gas water heater solenoid valve how bad the good times

Gas water heater solenoid valve how bad the good times
1, Gas Valve For Water Heater damage, can cause can not supply, generally just can not start her.
2, in the case of determining the normal ignition, the solenoid valve split out (off the gas source), then Bankai micro-switches, it will spark ignition, this time at the hand pads tap solenoid valve, solenoid valve It will pull, because there is no combustion, probably about 10 seconds the solenoid valve core will pop up, if they can so it should be good for him.
3, if you can not pull, it may be old or ignition battery has a problem.
4, magnet valve failure can be divided into the body, and an electromagnetic coil, spool valve failure is closed lax, open action is not in place or not, it can be opened manually to repair, and then there is the coil, and You can observe whether the appearance of burn state, whether smell paste flavor, touch is hot, with a table measuring coil values, the same as the original to see if the same comparison.
5, the easiest method is to determine, whether there is pull solenoid valve sound 'is "popping" sound, if no sound is bad